Cisco CCIE EI Lab ver 1.1 Dell R620 Server 1TB 256GB RAM SD-WAN 20.9 INE+Narbik

on May 23, 2024 • by admin

Cisco CCIE EI Lab ver 1.1 Dell R620 Server 1TB 256GB RAM SD-WAN 20.9 INE+Narbik

This is a Lab kit that for the new Cisco CCIE Enterprise Infrastructure Lab Exam ver 1.1. It includes an EVE-NG Virtual Machine loaded with Viptela SD-WAN Controllers. This Lab can be used with 2 different Lab Topologies: INE (ine. Com) and Narbik Kocharians (micronicstraining. Com). It is is built using a Dell R620 Server w/ 256GB RAM (up to 768GB) + 1TB SSD with VMware ESXi 6.7 The Dell R620 is a Powerful Server with 2 x Ten-Core Processors (Xeon E5-2660v2). Ten-Core Processors have 20 vCPU’s. Therefore, this Server has a total of 40 vCPU’s Physical Server’s Main Features : – 2 x Ten-Core Processors (Xeon E5-2660v2 ==> 40 vCPU’s) – 4 x Gigabit Ethernet Interfaces – 256GB RAM (supports up to 384GB) – 1TB SSD Drive (can be upgraded to 2TB or 4TB) – VMware ESXi 6.7 Enterprise Version (w/ Permanent License) Please also notice that a Monitor is not included. You’ll need a Monitor and a Keyboard to operate this Server. Main VM’s for the CCIE EI Lab : These are the main VM’s for the CCIE EI Lab: – 1 x EVE-NG ver 5.0.1 VM (needed to simulate a Viptela SD-WAN Network) – 1 x CML-2 ver 2.7.0 VM (License not included) – 1 x Windows 2019 Server VM with 180-day Trial version – 1 x Cisco ISE Server ver 3.1 (Identity Services Engine) with 90-Day Demo License – 1 x Ubuntu Server ver 20.04.2 configured with NSO (Network Services Orchestrator) – 4 x IOSv-L2 Virtual Switches built inside EVE-NG – 10 x CAT8000v Virtual Routers ver 17.9 built as independent VM’s CCIE EI v1.1 Equipment Requirements. The new version of the CCIE EI Lab Exam (ver 1.1) includes several changes. The updated List of requirements can be found at this URL. As this URL shows, the new CCIE EI Lab Exam requires the following Virtual Machines. Main Virtual Machines – Cisco CAT8000v (Replaces the old CSR Routers) with IOS XE ver 17.9 – Cisco IOSv-L3 Routers w/ IOS Software ver 15.8 – Cisco IOSv-L2 Switches w/ IOS Software ver 15.2 – Cisco DNA Center Release 2.3. X – Cisco SD-WAN (vManage, vBond, vSmart, vEdge) Software ver 20.9 Supporting Virtual Machines – Cisco Identity Services Engine (ISE) – Ubuntu Server ver 18.04.5 – Windows Server Our Lab includes all of the Virtual Machines mentioned above, but a DNA Center (DNAC). DNAC is not included because the Hardware Requirements to implement it as a VM are much higher! That is, a DNAC simply won’t run on a Dell R620. We would need an R630 as minimum to deploy a DNAC. However, we do offer a DNAC as an upgrade option. As mentioned before, this Lab can be used with 2 different Lab Topologies. INE (ine. Com) and. Narbik Kocharians (micronicstraining. Com). But they can be converted to Controller-Mode , which allows management through the vManage Controller. This Topology also requires 4 x LAN Switches, which can be either Virtual or Physical. We implement INE’s Topology in 2 different ways. Virtual Routers as Independent VM’s (CAT8000v Routers). Virtual Routers inside EVE-NG (IOSvL3 Routers). Virtual LAN Switches are implemented using the IOSv-L2 Software inside the EVE-NG VM. However, please notice that Cisco recommends using Physical Switches because the IOSv-L2 Software doesn’t provide some of the advanced functions needed for the Lab. IOSv-L2 Switches are good enough to provide basic connectivity and some basic L2/L3 functions. And this should be enough to do most Lab Exercises. But if you want to do more complex Lab Exercises that deal with more advanced Switching functions, then you may want consider getting 4 x Physical Switches Physical Switches can be connected to the Server at any time and they can be easily combined with Virtual Routers. Narkik’s Topology uses up to 20 x Virtual Routers , but the number of Routers (and Switches) varies for each Lab Exercise. All Narbik’s Lab Exercises are available as independent. UNL file s that can be loaded on EVE-NG. There is a large set of Lab Exercises available (with Solutions) and you can download the complete list from this URL. The EVE-NG Virtual Machine (VM) is perhaps the most important component of this Lab. EVE-NG Community Edition is a Network Simulator that doesn’t need a License ; that is, it’s a Free Product! As mentioned before, our EVE-NG VM can be used for either INE or Narbik Lab Exercises. Our EVE-NG VM provides full SD-WAN functionality! That is, it includes all the Network Nodes needed to implement a Viptela SD-WAN Network version 20.9.3 (as required by the new CCIE EI Lab Exam ver 1.1). This includes SD-WAN Controllers, also known as Control Plane Components, and WAN Edge Nodes : – vBond – vSmart – vManage WAN Edge Nodes, also known as the Data or Forwarding Plane Devices, can be implemented in 2 ways : – vEdge Cloud Routers – CSR1000v Cloud Routers (SD-WAN version). In our EVE-NG VM you’ll find a Fully Configured and ready to use Sample SD-WAN Network This is done just to demonstrate the full SD-WAN functionality of our EVE-NG VM. We provide all the Configuration Files that you can use to build your own SD-WAN Network. Our EVE-NG VM also includes the following Virtual Devices. CAT8000v Routers (version 17.9.3a) – CAT9000v Switches (version 17.10.1) So you can use these Virtual Devices either as independent VM’s or inside EVE-NG. Combining Virtual Routers with Virtual or Physical Switches. As mentioned before, the EVE-NG VM is also used to implement 4 x IOSv-L2 Switches But in addition to these Switches, the EVE-NG VM also includes a set of 10 x IOSv Routers That is, this Lab includes 2 sets of Virtual Routers : – 10 x CAT8000v Routers (built as Independent VM’s) – 10 x IOSv-L3 Routers (built inside the EVE-NG VM) So you could use either set of Virtual Routers, both of which can be connected to the set of Virtual Switches And if you add Physical Switches to the Lab, the Routers could be connected to either set of Switches (Virtual or Physical). So you’ll have 4 potential combinations : – CAT8000v Routers (CAT8Kv) connected to Virtual Switches – CAT8000v Routers (CAT8Kv) connected to Physical Switches – IOSv-L3 Routers connected to Virtual Switches – IOSv-L3 Routers connected to Physical Switches Of course you may also add extra Virtual Routers (CAT8Kv or IOSv) and extra IOSv Switches! Thus, this item provides a very flexible Lab environment with many configuration options! CML-2 VM : This Lab also includes a CML-2 VM because INE uses CML for many of their Lab Exercises. The VM included in this Lab doesn’t have a License though. However, you could use the EVE-NG VM instead of CML-2 for almost all Lab Exercises! Upgrade Options : As mentioned before, you may add 4 x Physical Switches to this Lab. This will allow you to work on some advanced features not available in the IOSv-L2 Software. There are a few options for the Physical Switches. It is also possible to upgrade some of the Server’s main features, such as RAM and Drive. A RAM upgrade may be needed to simulate large SD-WAN Networks, which are RAM hungry! The Server’s Drive capacity is 1TB, but it can be upgraded to 2TB or 4TB SSD. And as mentioned before, we also offer the possibility of adding a DNA Center! However, this would require a different Hardware (R630 instead of R620) provided either as a separate Server or a single Server with all VM’s in it. If you experience any problems, we’ll replace it! Please take this into account. Thank you for looking!

Cisco ACI Simulator Dell R620 128GB + EVE-NG Server CCNP CCIE Data Center Lab

on February 3, 2024 • by admin

Cisco ACI Simulator Dell R620 128GB + EVE-NG Server CCNP CCIE Data Center Lab

This is a Cisco ACI Simulator (Application Centric Infrastructure) version 5.2-5c. The ACI Simulator is a Virtual Machine Appliance that simulates a Cisco ACI environment. It does it by creating a Network of several APIC Controllers Application Policy Infrastructure Cont. With Cisco ACI Spines and Cisco ACI Leafs. This is a great tool for the CCNP and even CCIE DC (Data Center) Exams. This Simulator is implemented on a Dell R620 Server with 128GB RAM + 1TB SSD Drive. The Server also includes an EVE-NG VM with Nexus 7000 & 9000 Virtual Switches (NX-OSv 7K & 9K). This provides the ability to create a separate Leaf & Spine Switch Nodes within the EVE-NG VM. The EVE-NG VM also includes Network Nodes needed to emulate a Viptela SD-WAN Network. The R620 Server comes with 2 x Ten -Core Processors (Xeon E5-2660v2). Ten-Core Processors have 20 vCPU’s. Therefore, this Server has a total of. These are the main features of the Dell R620 Server used to build this Lab: – 2 x Ten-Core Processors Xeon E5-2660 or higher. 4 x Gigabit Ethernet Interfaces – – 128GB RAM can grow up to 768GB! – 1TB SSD Drive (can be upgraded to 2TB SSD) – Operating System. VMware ESXi 6.5 Raw Metal Virtualization OS. Please notice that the Monitor is not included. You’ll need a Monitor and a Keyboard to operate this Server. This System actually implements 2 main VM’s (each one is a separate Virtual Machine). Cisco ACI Simulator. (Emulated Virtual Environment-Next Generation). Ver 5.0.1. In addition, this Server also includes the following VM. Cisco CML-2 Server. (Cisco Modeling Labs) ver 2.6.1. (Latest version, 90-Day License included). The main features of the ACI Simulator don’t require a License. But some special/advanced features do need a License. However, in case that you need to use any of these. Advanced features, you can register the Product to obtain. Evaluation License (or Demo License). With a 90 Days Validity Period. If you need to use the. Advanced features after 90 days after. The Evaluation License expires you can simply re-install the VM. OVA file needed for this purpose. The ACI Simulator can be re-installed an unlimited number of times! Therefore, it can be used indefinitely! The EVE-NG Server includes Nexus 7K & 9K Virtual Switches that allow you to create Leaf & Spine Switch Nodes. This Server will also let you simulate all the Network Nodes needed to implement a. This includes the SD-WAN Controllers, also known as Control Plane Components. VBond – vSmart – vManage. And the WAN Edge Nodes, also known as the Data or Forwarding Plane Devices. The SD-WAN Controllers use the most recently approved version: 20.9.3 The WAN Edge Nodes can be implemented with the Viptela vEdge Software ; also version 20.9.3. But they can also be implemented with a CSR1000v Router or with a CAT8000v Router. We include the following versions. CSR1000v with IOS XE version 16.12.5 – CAT8000v with IOS XE version 17.9 (latest version). For a complete list of the Virtual Devices included with this Server. Is a Free, Open Source Software that can be used to simulate complex networks. CML-2 is a Cisco Licensed Software that can also be used to simulate complex networks. The main advantage of EVE-NG over CML is the fact that while CML provides a Cisco-only environment, EVE-NG is NOT limited to Cisco Devices! EVE-NG provides a Multi-vendor environment! That is, it allows you to emulate complex Networks with all kinds of Network Devices! Please scroll down for more specific differences between EVE-NG and CML. Please also notice that the item price doesn’t include the License for CML-2. Important Note about the CML-2 License. However, some Virtual Devices do work better and faster under CML than under EVE-NG. Just like all Servers, this item needs a separate computer (Client PC) to manage the Server and its VM’s. Typical Server Management tasks include. Power up/Power down VM’s, Assign VLAN’s and Network Ports to the VM’s, etc. The ESXi Server can be managed using either special Software known as the. Both computers (Server and Client PC) must be connected to a LAN Switch that could be your Home Router/Switch from your ISP. Using your Home Router/Switch will the Server access to the Internet, which could be needed for some tasks. Server comes with 128GB RAM. But RAM can grow up to 768GB! These are some other upgrade options available. 1TB SSD Drive upgrade to 2TB or even 4TB SSD. Please write to us for details about these Upgrade options. These are some of the most important features of the Cisco CML-2 Software : – Includes Official Cisco Images it is the only Tool fully Licensed and approved by Cisco! – Multiple Network Platforms (IOSv, IOSvL2, NX-OSv, IOS XRv, IOS-XEv and ASAv Firewall) CML-2 comes with a complete set of Legal and Fully Licensed Cisco IOS Images that are the same as those running on physical Routers & Switches. New Cisco IOS releases are provided in a regular basis. So you’ll always have the most up to date Virtual IOS Images! It supports the classic IOS Images found in common ISR Routers and Layer 2 Switches. It doesn’t support Layer 3 Switches yet, but it might do so in the near future. In addition to the classic IOS Images, CML supports advanced Platforms such as. (used in Service Provider environments) It also supports the. That can be used for Security related tasks. Finally, it also supports. Which is the virtual version of the Cisco IOS XE Software that comes in the newest ISR Routers like the 42XX, 43XX and 44XX Series! Like GNS3, EVE-NG is Free because it doesn’t include the actual IOS Images needed to boot the Virtual Devices in your Network. Without the proper IOS Images, EVE-NG alone would be basically useless! Therefore, you’d need to provide these IOS Images and upload them to EVE-NG. GNS3 & EVE-NG Users normally struggle trying to find the proper IOS Images. However, our EVE-NG Server is already pre-loaded with multiple IOS Images! As mentioned before, our EVE-NG Server includes all the Network Nodes needed to emulate a. In addition, our Server is pre-loaded with the following IOS Images. Cisco IOSv Router version 15.9.3 – Cisco XRv Router version 6.3.1 – Cisco XRv-9K Router version 7.2.1 – Cisco CSR1000v and CAT8000v Routers versions 16.2 and 17.9 Switches – Cisco NX-OSv 9K Nexus Switch version 9.2.2 – Cisco NX-OSv 7K Titanium Nexus version 7.3.0 – Cisco Layer-2 Switch with IOSv-L2 version 15.2. You can create multiple instances of these Virtual Devices, which are fully setup and ready to use! You can also implement many other Virtual Devices, provided that you upload the proper IOS Image for them. This Virtual Lab has been fully tested and. Therefore it’s guaranteed to work! I f you have any questions about the operation of this Virtual Lab, you can always count on us We’ve been providing Networking Training Kits for years with hundreds of very satisfied customers! Please notice that due to the complex nature of this item we need. 2-3 days for processing. (it depends on where you live). Thank you for looking!

EVE-NG CML Server Viptela SD-WAN Contr Dell R620 128GB RAM Cisco CCNP CCIE Lab

on November 1, 2023 • by admin

EVE-NG CML Server Viptela SD-WAN Contr Dell R620 128GB RAM Cisco CCNP CCIE Lab

This is an EVE-NG Server that includes Network Nodes needed to emulate a Viptela SD-WAN Network! This Server can be used as a CCNP/CCIE Lab, since it includes all the elements need for that purpose. It is based on a Dell R620 Hardware with 128GB RAM + 1TB SSD Drive. The Dell R620 is a very quiet Server that is loaded with VMware ESXi 6.5. This Server comes with 2 x Ten-Core Processors (Xeon E5-2660v2). Ten-Core Processors have 20 vCPU’s. Therefore, this Server has a total of 40 vCPU’s. This System actually includes 2 main VM’s (each one is a separate Virtual Machine). Cisco CML-2 Server (Cisco Modeling Labs) ver 2.6.0 (latest version) – EVE-NG Server Emulated Virtual Environm. Ver 5.0.1 w/ SD-WAN Support Please notice that CML-2 is licensed product from Cisco. License is not included though. However, EVE-NG Community Edition (free version) does NOT require a License. In addition, this Server includes the following VM’s. Windows 2019 Server (with 180-Day Demo License) – Ubuntu Server ver 20.04.2 (with NSO). This EVE-NG Server includes all the Network Nodes needed to emulate a Viptela SD-WAN Network! This includes the SD-WAN Controllers, also known as Control Plane Components: – vBond – vSmart – vManage And the WAN Edge Nodes, also known as the Data or Forwarding Plane Devices: – vEdge The SD-WAN Controllers use the most recent version: 20.9.3 The WAN Edge Nodes can be implemented with the Viptela vEdge Software ; also version 20.9.3 But they can also be implemented with a CSR1000v Router or with a CAT8000v Router. Include the following versions. CSR1000v with IOS XE version 16.12.5 – CAT8000v with IOS XE version 17.9. Please scroll down for a complete list of the Virtual Devices included with this Server. These are the main features of the Dell R620 used to build this Virtual Lab: – 2 x Quad Core Processors (Xeon E5-2660 or higher) – 4 x Gigabit Ethernet Interfaces – – 128GB RAM can grow up to 768GB! – 1TB SSD Drive (can be upgraded to 2TB SSD) – Operating System: VMware ESXi 6.5 Raw Metal Virtualization OS Having your own Lab (own Physical Server) makes a lot more sense than Renting a Physical or Virtual one! This will really add up in the long run! Please attached image with Reference Prices. Note: Please notice that the Monitor is not included. You’ll need a Monitor and a Keyboard to operate this Server. Is a Free, Open Source Software that can be used to simulate complex networks. CML-2 is a Cisco Licensed Software that can also be used to simulate complex networks. The main advantage of EVE-NG over CML is the fact that while CML provides a Cisco-only environment, EVE-NG is NOT limited to Cisco Devices! EVE-NG provides a Multi-vendor environment! That is, it allows you to emulate complex Networks with all kinds of Network Devices! Please scroll down for more specific differences between EVE-NG and CML. Please also notice that the item price doesn’t include the License for CML-2. Client Software NOT needed. CML-2 and EVE-NG are VM’s that run on the Physical Dell Server. But these are just Back-End Processes that don’t have a User Interface! In order to actually use these VM’s you’ll need a separate computer (a regular PC), that will be the Client PC. Typical Management tasks include. Power up/Power down VM’s, Assign VLAN’s and Network Ports to the VM’s, etc. The ESXi Server can be managed using another special Software known as the vSphere Client , which of course must also be installed in the Client PC. Upgrade Options : Server comes with 128GB RAM. But RAM can grow up to 768GB! These are some other upgrade options available: – 1TB SSD Drive upgrade to 2TB SSD – Drive can also be upgraded to RAID (RAID-1 or RAID-6), but more Drives would be needed. Please write to us for details about these Upgrade options. CML Main Features : These are some of the most important features of the Cisco CML-2 Software : – Includes Official Cisco Images it is the only Tool fully Licensed and approved by Cisco! – Multiple Network Platforms (IOSv, IOSvL2, NX-OSv, IOS XRv, IOS-XEv and ASAv Firewall). CML-2 comes with a complete set of Legal and Fully Licensed Cisco IOS Images that are the same as those running on physical Routers & Switches. New Cisco IOS releases are provided in a regular basis. So you’ll always have the most up to date Virtual IOS Images! It supports the classic IOS Images found in common ISR Routers and Layer 2 Switches: IOSv & IOSvL2 It doesn’t support Layer 3 Switches yet, but it might do so in the near future. In addition to the classic IOS Images, CML supports advanced Platforms such as IOS XRv & XRv 9000 (used in Service Provider environments) It also supports the ASAv Firewall , that can be used for Security related tasks. The new CML-2 version 2.5.1 also includes a pair of very powerful Virtual Appliances; Catalyst 8000v Edge Router and the Catalyst 9000v Virtual Switch , which provide very advanced functions not available in other (older) Appliances. Finally, CML-2 also supports IOS-XEv , which is the virtual version of the Cisco IOS XE Software that comes in the newest ISR Routers like the 42XX, 43XX and 44XX Series! Like GNS3, EVE-NG is Free because it doesn’t include the actual IOS Images needed to boot the Virtual Devices in your Network. Without the proper IOS Images, EVE-NG alone would be basically useless! Therefore, you’d need to provide these IOS Images and upload them to EVE-NG. GNS3 & EVE-NG Users normally struggle trying to find the proper IOS Images. However, our EVE-NG Server is already pre-loaded with multiple IOS Images! As mentioned before, our EVE-NG Server includes all the Network Nodes needed to emulate a Viptela SD-WAN Network! In addition, our Server is pre-loaded with the following IOS Images. Routers – Cisco IOSv Router version 15.9.3 – Cisco XRv Router version 6.3.1 – Cisco XRv-9K Router version 7.2.1 – Cisco CSR1000v with IOS XE version Amsterdam 16.12 Other Devices – Cisco ASAv Firewall version 9.14.1 – Cisco NX-OSv9K Nexus Switch version 9.2.4 – Cisco Layer-2 Switch with IOSv-L2 version 15.2. You can create multiple instances of these Virtual Devices, which are fully setup and ready to use! You can also implement many other Virtual Devices, provided that you upload the proper IOS Image for them. This Virtual Lab has been fully tested and. Therefore it’s guaranteed to work! I f you have any questions about the operation of this Virtual Lab, you can always count on us We’ve been providing Networking Training Kits for years with hundreds of very satisfied customers! Please notice that due to the complex nature of this item we need. 2-3 days for processing. (it depends on where you live). Thank you for looking!

Cisco CCIE Security Virtual Lab INE Dell T5600 128GB RAM 1TB SSD ISE FMC CSR1000

on July 30, 2022 • by admin

Cisco CCIE Security Virtual Lab INE Dell T5600 128GB RAM 1TB SSD ISE FMC CSR1000

This is a Server-based Home Lab for the CCIE Security v6 Lab Exam. It is based on INE’s recommendations (Inter Network Expert) for this CCIE Lab Exam. Lab is built using a Dell T5600 Server w/ 128GB RAM Max. RAM + 1TB SSD HD with VMware ESXi 6.5 It includes 2 x Hex-Core Processors (Xeon E5-2620 or higher). This Server is running VMware ESXi 6.5 Enterprise Version with a Permanent Enterprise License. These are the main technical specifications of this CCIE Virtual Lab: – 2 x Hex-Core Processors – Xeon E5-2620 or higher – 4 x Gigabit Ethernet Interfaces – 128GB RAM Max. RAM – 1TB SSD Hard Drive – VMware ESXi Enterprise 6.5 (Permanent License included) – 11 Instances of the Cisco CSR-1000v Virtual Router with IOS XE version 16.9.5 – 21 Security Virtual Appliances ACSv, ISEv, ESAv, FTDv, FMCv, NGIPSv, ASAv, etc. Please also notice that a Monitor is not included. You’ll need a Monitor and a Keyboard to operate this Server. V6 Lab Topology : The Topology for CCIE Security Lab v6 is actually very similar to that of the previous version (v5). That is because there have been very few changes in the v6 Exam. Therefore, INE is still using the v5 Lab Topology for all Lab Training. This Topology is illustrated in the Image No. The original installation Software is also included. This Lab has been configured according to INE’s CCIE Security Network Diagram. Although you could Manage the Server with a single Management Station (PC or Laptop), it is recommended to have 2 separate PC’s for Management purposes. PC-1 is the standard Client-PC that all Servers need and it’s also used for Out-of-Band Management. PC-2 is the In-band Management PC. It’s used to connect to the Management Interface of each Virtual Appliance. Please notice that a full CCIE Security Lab based on INE’s Topology requires some Physical Devices. Server’s RAM can also be upgraded from 128GB to 256GB or all the way up to 768GB Max. SSD Drive can be upgraded from 1TB to 2TB. Or a second 1TB SSD Drive can be added for 2nd Data Storage. Virtual Device Licenses : Most Virtual Appliances come with a Trial/Demo License. In most cases this Demo License can be reset by re-installing the. The original installation Software is provided for that purpose. A few Appliances and the ESXi Server itself do have a Permanent License though! This is a summary of the Licenses for each. ISEv: 90-Day Trial License (it must be re-installed after 90 days) – WLCv: 90-Day Trial License (it must be re-installed after 90 days) – FTDv: 90-Day Trial License (it must be re-installed after 90 days) – FMCv: 90-Day Trial License (it must be re-installed after 90 days) – WSAv: 30-Day Trial License (it needs a new License after Trial Period) – ESAv: 30-Day Trial License (it needs a new License after Trial Period) – ACSv: Permanent License! – ESXi Server: Permanent Enterprise Version License! – Test Stations (Windows 2008 Server): Permanent License! – NGIPSv: No License! (Please see note about this Appliance below) – ASAv: Lab Edition Mode (No License), but still fully functional. Data Rate limited to 100Kbps – CSR1000v: Lab Edition Mode (No License), but still fully functional. Data Rate limited to 2.5Mbps Note about CSR1000v Licenses – CSR1000v Routers are configured in Lab Edition Mode (No License), but they are still fully functional. While in Lab Mode the Router is fully functional with an AX License with IPBase + APPX + Security functions – The Data Rate in Lab Mode is limited to 2.5Mbps, which is enough for a Lab environment. Note about WSAv & ESAv Licenses. Demo Licenses for the WSAv & ESAv Appliances last for only 30 days. After this 30-day period you’ll need a new Demo License, which can be obtained from Cisco. You’ll need to contact Cisco directly to obtain these Licenses. Note about NGIPSv Licenses – There are no Trail/Demo Licenses available for the NGIPSv Virtual Appliance – However, for almost all practical purposes, FTDv replaces NGIPSv! – An FTDv Appliance is considered to be an NGIPSv with a ASAv included! – So in a way, FTDv actually provides more functions than NGIPSv – Therefore, for almost all practical purposes FTDv replaces NGIPSv! Server is fully tested and. Therefore it’s guaranteed to work. If you experience any problems, we’ll replace it. However, that’s very unlikely to happen. (please check out our Feedback Record). We’ve been providing Cisco Training Kits for years with hundreds of very satisfied customers. Please notice that due to the VERY complex nature of this item we need. 3-4 days for processing. (it depends on where you live). Or to International destinations is also available. Thank you for looking! List of VLAN’s configured in the Server. Cisco IOS XE Software, Version 03.16.06. Certain components of Cisco IOS-XE software are licensed under the GNU General Public License (“GPL”) Version 2.0. You can redistribute and/or modify such GPL code under the terms of GPL Version 2.0. For more details, see the documentation or “License Notice” file accompanying the IOS-XE software, or the applicable URL provided on the flyer accompanying the IOS-XE software. Conf Last reload reason: Unknown reason This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Importers, exporters, distributors and users are responsible for compliance with U. And local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U. And local laws, return this product immediately. A summary of U. Processor board ID 9VPXPG8FE8Y 3 Gigabit Ethernet interfaces 32768K bytes of non-volatile configuration memory. 3988272K bytes of physical memory. 7774207K bytes of virtual hard disk at bootflash. Configuration register is 0x2102. Changes from version 5.0 to 6.0 : These are the main Topics for the CCIE Security Lab Exam version 6.0 1. Perimeter Security and Intrusion Prevention (20%) 2. Secure Connectivity and Segmentation (20%) 3. Infrastructure Security (15%) 4. Advanced Threat Protection and Content Security (20%) And these are Exam Topics for the previous version 5.0 1. Perimeter Security and Intrusion Prevention (23%) 3. Secure Connectivity and Segmentation (19%) 5. Infrastructure Security, Virtualization, and Automation (15%) 4. Advanced Threat Protection and Content Security (19%) 6. Evolving Technologies The order was changed to make the comparison easier. As you may notice, version 6.0 is almost exactly the same as version 5.0! Chapter 6 in version 5.0 (Evolving Technologies) has been removed. That’s because most of these Technologies are now Mainstream Technologies, so they’ve been included in the main Chapters. INE CCIE Security v6.0 Topics. Routing & Switching Technologies Review 3. Perimeter Security and Intrusion Prevention 4. Cryptography and Virtual Private Networks 5. Infrastructure Security, Attacks and Mitigation 6. Access Control and Identity Services Engine 7. Programmability and Automation 8. Content Security and Advanced Threat Protection 9. CCIE Security v5 Lab Preparation Course 10. This item is in the category “Computers/Tablets & Networking\Enterprise Networking, Servers\Servers, Clients & Terminals\Computer Servers”. The seller is “training.kits” and is located in this country: US. This item can be shipped worldwide.

Network Connectivity: Wired-Ethernet (RJ-45)
Model: T5600
Network Type: Gigabit Ethernet
Number of Processors: 2
Interface: Ethernet (RJ-45)
Product Line: PowerEdge
Network Management Type: Fully Managed
Type: Server
Maximum RAM Capacity: 768GB
MPN: Dell-T5600
RAM Size: 128GB
Brand: Dell
Form Factor: Rack Mountable
Processor Manufacturer: Intel

EVE-NG Server + Cisco CML-2 Network Lab Dell R620 128GB CCNP CCIE Viptela SD-WAN

on August 19, 2021 • by admin

EVE-NG Server + Cisco CML-2 Network Lab Dell R620 128GB CCNP CCIE Viptela SD-WAN

But in some cases it may be possible to remove this extra charge. This is an EVE-NG Server that includes Network Nodes needed to emulate a Viptela SD-WAN Network! This Server is based on a Dell R620 Hardware with 128GB RAM + 1TB Drive. This System actually implements 3 different Servers (each one is a separate Virtual Machine). Cisco CML-2 Server (Cisco Modeling Labs) version 2.1.2 (latest version) – Cisco VIRL Server (Virtual Internet Routing Lab) version 1.6.67 (now replaced with CML-2) – EVE-NG Server (Emulated Virtual Environment-Next Generation) Community Edition version 2.0.3-112 Please notice that this is the Community Edition (free version), not the Pro version , which requires a License. By the way, we can also provide the Pro version if needed. The Hardware is a very quiet Dell R620 Server with 128GB RAM running VMware ESXi 6.5 This EVE-NG Server includes all the Network Nodes needed to emulate a Viptela SD-WAN Network! This includes the SD-WAN Controllers , also known as Control Plane Components: – vBond – vSmart – vManage And the WAN Edge Nodes , also known as the Data or Forwarding Plane Devices: – vEdge The SD-WAN Controllers use the most recently approved versions: 19.2.31 and 20.3.2 The WAN Edge Nodes can be implemented with the Viptela vEdge Software ; also versions 19.2.31 or 20.3.2 But they can also be implemented with the CSR1000v SD-WAN Router , which now can be managed by SD-WAN Controllers We include 2 versions of the CSR1000v SD-WAN Router: – CSR1000v with IOS XE version UCM-K9 16.12.5 – CSR1000v with IOS XE version Amsterdam 17.3.2 latest version! Please scroll down for a complete list of the Virtual Devices included with this Server. These are the main features of the Dell R620 used to build this Virtual Lab: – 2 x Quad Core Processors (Xeon E5-2609 or higher) – 4 x Gigabit Ethernet Interfaces – – 128GB RAM can grow up to 768GB! – 1TB Drive (can be upgraded to 1TB SSD or 2TB SSD) – Operating System: VMware ESXi 6.5 Raw Metal Virtualization OS Having your own Lab (own Physical Server) makes a lot more sense than Renting a Physical or Virtual one! This will really add up in the long run! Please attached image with Reference Prices. Note: Please notice that the Monitor is not included. You’ll need a Monitor and a Keyboard to operate this Server. Is a Free , Open Source Software that can be used to simulate complex networks. CML & VIRL are Cisco Licensed Software that can also be used to simulate complex networks. The main advantage of EVE-NG over CML is the fact that while CML provides a Cisco-only environment , EVE-NG is NOT limited to Cisco Devices! EVE-NG provides a Multi-vendor environment! That is, it allows you to emulate complex Networks with all kinds of Network Devices! Please scroll down for more specific differences between EVE-NG and CML. Please also notice that the item price doesn’t include the License for CML-2/VIRL. We’ll bill you the proper cost. Client Software NOT needed. VIRL, CML-2 and EVE-NG are VM’s that run on the Physical Dell Server. But these are just Back-End Processes that don’t have a User Interface! In order to actually use these VM’s you’ll need a separate computer (a regular PC), that will be the Client PC. The only exception is the VIRL VM, which does need a special Client Software to be installed in the Client PC. This special Software is called VM Maestro Client Software. Typical Management tasks include. Power up/Power down VM’s, Assign VLAN’s and Network Ports to the VM’s, etc. The ESXi Server can be managed using another special Software known as the vSphere Client , which of course must also be installed in the Client PC. Upgrade Options : Server comes with 128GB RAM. But RAM can grow up to 768GB! These are some other upgrade options available: – 1TB Hard Drive upgrade to 1TB SSD or 2TB SSD – HD can also be upgraded to RAID (RAID-1, RAID-5 or RAID-6). Please write to us for details about these Upgrade options. CML/VIRL Main Features : These are some of the most important features of the Cisco CML/VIRL Software : – Includes Official Cisco Images it is the only Tool fully Licensed and approved by Cisco! – Multiple Network Platforms (IOSv, IOSvL2, NX-OSv, IOS XRv, IOS-XEv and ASAv Firewall). CML/VIRL comes with a complete set of Legal and Fully Licensed Cisco IOS Images that are the same as those running on physical Routers & Switches. New Cisco IOS releases are provided in a regular basis. So you’ll always have the most up to date Virtual IOS Images! It supports the classic IOS Images found in common ISR Routers and Layer 2 Switches: IOSv & IOSvL2 It doesn’t support Layer 3 Switches yet, but it might do so in the near future. In addition to the classic IOS Images, VIRL supports advanced Platforms such as IOS XRv & XRv 9000 (used in Service Provider environments) It also supports the ASAv Firewall , that can be used for Security related tasks. Finally, it also supports IOS-XEv , which is the virtual version of the Cisco IOS XE Software that comes in the newest ISR Routers like the 42XX, 43XX and 44XX Series! Like GNS3, EVE-NG is Free because it doesn’t include the actual IOS Images needed to boot the Virtual Devices in your Network. Without the proper IOS Images, EVE-NG alone would be basically useless! Therefore, you’d need to provide these IOS Images and upload them to EVE-NG. GNS3 & EVE-NG Users normally struggle trying to find the proper IOS Images. However, our EVE-NG Server is already pre-loaded with multiple IOS Images! As mentioned before, our EVE-NG Server includes all the Network Nodes needed to emulate a Viptela SD-WAN Network! In addition, our Server is pre-loaded with the following IOS Images. Routers – Cisco IOSv Router version 15.9.3 – Cisco XRv Router version 6.3.1 – Cisco XRv-9K Router version 7.2.1 – Cisco CSR1000v SD-WAN Router with IOS XE version Amsterdam 17.3.2 Other Devices – Cisco ASAv Firewall version 9.14.1 – Cisco NX-OSv9K Nexus Switch version 9.2.4 – Cisco Layer-2 Switch with IOSv-L2 version 15.2. You can create multiple instances of these Virtual Devices, which are fully setup and ready to use! You can also implement many other Virtual Devices, provided that you upload the proper IOS Image for them. Bonus Software and Training Materials : This item includes a Disk (DVD) with the following Software and Training Materials : – VMware vSphere 6.0 Client Software (needed only for special purposes) – VMware ESXi 6.5 Operating System Installation Files (ISO CD Image) – mRemoteNG Connections Manager (provides Telnet/SSH access to the virtual devices) – VM Maestro Client Software (Maestro must be installed in a separate computer) – VIRL Training Videos (Videos about the installation, configuration and use of VIRL) – EVE-NG Training Videos (Links to YouTube Videos with useful EVE-NG Tips and Tricks). This Virtual Lab has been fully tested and. Therefore it’s guaranteed to work! I f you have any questions about the operation of this Virtual Lab, you can always count on us We’ve been providing Networking Training Kits for years with hundreds of very satisfied customers! Please notice that due to the complex nature of this item we need. 2-3 days for processing. (it depends on where you live). Thank you for looking! The item “EVE-NG Server + Cisco CML-2 Network Lab Dell R620 128GB CCNP CCIE Viptela SD-WAN” is in sale since Thursday, February 25, 2021. This item is in the category “Computers/Tablets & Networking\Enterprise Networking, Servers\Servers, Clients & Terminals\Computer Servers”. The seller is “training.kits” and is located in Gainesville, Florida. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Mexico, Canada, Australia.

Model: R620
RAID Levels: 0
Type: Server
MPN: Does Not Apply
RAM Size: 128GB
Brand: Dell
Number of Processors: 2
Product Line: PowerEdge
Maximum RAM Capacity: 768GB
Processor Manufacturer: Intel

Cisco VIRL & GNS3 Server Dell R610 48GB VMware ESXi 6 CCNA CCNP CCIE Virtual Lab

on May 12, 2020 • by admin

Cisco VIRL & GNS3 Server Dell R610 48GB VMware ESXi 6 CCNA CCNP CCIE Virtual Lab

But in some cases it may be possible to remove this extra charge. This is a Dell R610 Server that implements a Virtual Lab combining the following Products: – GNS3 VM Server (Graphical Network Simulator 3) version 2.2.5 (latest version as of March/2020) – Cisco VIRL Server (Virtual Internet Routing Lab) version 1.6.65 (latest version as of March/2020) Both Products run on an VMware ESXi Server version 6.0 It is built using an Ultra Quiet Dell R610 Server with 48GB RAM and a 500GB HD This Virtual Lab is a great tool for most Cisco CCNA, CCNP and CCIE Certifications. It can be used for several Certification Tracks such as R&S, SP (Service Provider), Data Center, Security, etc. These are the main features of the Dell R610 used to build this Virtual Lab: – 2 x Quad Core Processors (8 Cores Total) – 4 x Gigabit Ethernet Interfaces – – 48GB RAM – 500GB Hard Drive – Operating System: VMware ESXi 6.0 Raw Metal Virtualization OS This Virtual Lab includes the following VM’s (Virtual Machines). GNS3 VM Server (Graphical Network Simulator 3) version 2.2.3 – Cisco VIRL Server (Virtual Internet Routing Lab) version 1.6.65 – Windows 2012 Server ; 180-day Trail version. Note: Please notice that the Monitor is not included. You’ll need a Monitor and a Keyboard to operate this Server. GNS3 is a Free , Open Source Software that can be used to simulate complex networks. VIRL is a Cisco Licensed Software that can also be used to simulate complex networks. This Server includes both Software Products, although it does not include a VIRL License! If needed, we can assist you with the VIRL License installation process. Both Products need a separate PC to run a Client Software that interacts with the respective Server: – GNS3 GUI Software – VM Maestro Client Software Both are Windows-based tools used to create the actual Network Topology that you are seeking to simulate. This same Client PC is also used to install the vSphere Client to manage the ESXi Server. Important Note about VIRL License : – Price of this item does NOT include the VIRL License! If needed, License must be bought by the Customer. Upgrade Options : These are the upgrade options available: – Hard Drive upgrade to 1TB : 2 x 500GB Hard Drives with RAID-0 or RAID-1 configuration. Hard Drive can also be upgraded to SSD Drive , either 500GB or 1TB SSD. We can also add other Software components to this Server, like CUCM (Cisco Unified Call Manager) version 12.0 That way you can have a single multi-purpose Server for different Cisco Certifications! Please write to us for details about these Upgrade options. Cisco VIRL is a network design and simulation environment that includes a Graphical User Interface (GUI) implemented with the VM Maestro Client Software. Cisco VIRL supports up to 20 Network Nodes. Therefore, you can build very complex Lab environments with this Virtual Lab. VIRL Main Features : These are some of the most important VIRL features: – Includes Official Cisco Images VIRL is the only Tool fully Licensed and approved by Cisco! – Automatic Configuration (done with the AutoNetkit Tool) – Multiple Network Platforms (IOSv, IOSvL2, NX-OSv, IOS XRv, IOS-XEv and ASAv Firewall). VIRL comes with a complete set of Legal and Fully Licensed Cisco IOS Images that are the same as those running on physical Routers & Switches. New Cisco IOS releases are provided in a regular basis. So you’ll always have the most up to date Virtual IOS Images! VIRL supports the classic IOS Images found in common ISR Routers and Layer 2 Switches: IOSv & IOSvL2 VIRL does not support Layer 3 Switches yet, but it might do so in the near future. In addition to the classic IOS Images, VIRL supports advanced Platforms such as IOS XRv & XRv 9000 (used in Service Provider environments) It also supports the ASAv Firewall , that can be used for Security related tasks. Finally, VIRL also supports IOS-XEv , which is the virtual version of the Cisco IOS XE Software that comes in the newest ISR Routers like the 42XX, 43XX and 44XX Series! GNS3 VM Features : These are some of the most important GNS3 VM features : – It supports Standard IOS (Legacy IOS) and VIRL IOS Images (GNS3 2.0 and higher) – Cisco Images are not embedded like in VIRL, so they must be obtained separately. By using VIRL Images, GNS3 provides support for IOS 15. X (IOSv, IOSvL2 & IOS XEv) – All work is done on the GNS3 Client PC! The GNS3 VM only provides back-end services. One of the traditional limitations of GNS3 is the fact that it doesn’t include ANY Cisco Images. So although you can download & install GNS3 for Free, normally you won’t be able to do anything with it. GNS3 users normally struggle trying to find IOS Images that can be imported into it. As mentioned above, GNS3 now can also import VIRL Images, which provides support for IOS 15. Bonus Software and Training Materials : This item includes a Disk (DVD) with the following Software and Training Materials : – VMware vSphere 6.0 Client Software – VMware ESXi 6.0 Operating System Installation Files (ISO CD Image) – mRemoteNG Connections Manager (provides Telnet/SSH access to the virtual devices) – VM Maestro Client Software (Maestro must be installed in a separate computer) – VIRL Training Videos Materials (Videos about the installation, configuration and use of VIRL) – GNS3 GUI and Server Software (GUI must also be installed in a separate computer) – GNS3 Training Videos Materials (Videos about the installation, configuration and use of GNS3). This Virtual Lab has been fully tested and. Therefore it’s guaranteed to work! I f you have any questions about the operation of this Virtual Lab, you can always count on us We’ve been providing Cisco Training Kits for years with hundreds of very satisfied customers! Please notice that due to the complex nature of this item we need. 2-3 days for processing. (it depends on where you live). Thank you for looking! The item “Cisco VIRL & GNS3 Server Dell R610 48GB VMware ESXi 6 CCNA CCNP CCIE Virtual Lab” is in sale since Monday, June 18, 2018. This item is in the category “Computers/Tablets & Networking\Enterprise Networking, Servers\Servers, Clients & Terminals\Computer Servers”. The seller is “training.kits” and is located in Gainesville, Florida. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Australia.

Model: R610
RAID Levels: 0
MPN: Does Not Apply
Brand: Dell
Number of Processors: 2
Memory (RAM) Capacity: 48GB

Cisco VIRL & GNS3 Server Dell R610 32GB VMware ESXi 6 CCNA CCNP CCIE Virtual Lab

on February 21, 2020 • by admin

Cisco VIRL & GNS3 Server Dell R610 32GB VMware ESXi 6 CCNA CCNP CCIE Virtual Lab

This is a Dell R610 Server that implements a Virtual Lab combining the following Products: – GNS3 VM Server (Graphical Network Simulator 3) version 2.2.3 (latest version as of Nov/16/2019) – Cisco VIRL Server (Virtual Internet Routing Lab) version 1.6.65 (latest version as of Nov/16/2019) Both Products run on an VMware ESXi Server version 6.0 It is built using an Ultra Quiet Dell R610 Server with 32GB RAM and a 500GB HD This Virtual Lab is a great tool for most Cisco CCNA, CCNP and CCIE Certifications. It can be used for several Certification Tracks such as R&S, SP (Service Provider), Data Center, Security, etc. These are the main features of the Dell R610 used to build this Virtual Lab: – 2 x Quad Core Processors (8 Cores Total) – 4 x Gigabit Ethernet Interfaces – – 32GB RAM (can be upgraded to 48GB) – 500GB Hard Drive (can be upgraded to SSD Drive) – Operating System: VMware ESXi 6.0 Raw Metal Virtualization OS This Virtual Lab includes the following VM’s (Virtual Machines). GNS3 VM Server (Graphical Network Simulator 3) version 2.2.3 – Cisco VIRL Server (Virtual Internet Routing Lab) version 1.6.65 – Windows 2012 Server ; 180-day Trail version. Note: Please notice that the Monitor is not included. You’ll need a Monitor and a Keyboard to operate this Server. GNS3 is a Free , Open Source Software that can be used to simulate complex networks. VIRL is a Cisco Licensed Software that can also be used to simulate complex networks. This Server includes both Software Products, although it does not include a VIRL License! If needed, we can assist you with the VIRL License installation process. Both Products need a separate PC to run a Client Software that interacts with the respective Server: – GNS3 GUI Software – VM Maestro Client Software Both are Windows-based tools used to create the actual Network Topology that you are seeking to simulate. This same Client PC is also used to install the vSphere Client to manage the ESXi Server. Important Note about VIRL License : – Price of this item does NOT include the VIRL License! If needed, License must be bought by the Customer. Upgrade Options : Server’s RAM can be upgraded to 48GB (up from 32GB). These are some other upgrade options available: – Hard Drive upgrade to 1TB : 2 x 500GB Hard Drives with RAID-0 or RAID-1 configuration. Hard Drive can also be upgraded to SSD Drive , either 500GB or 1TB SSD. We can also add other Software components to this Server, like CUCM (Cisco Unified Call Manager) version 12.0 That way you can have a single multi-purpose Server for different Cisco Certifications! Please write to us for details about these Upgrade options. Cisco VIRL is a network design and simulation environment that includes a Graphical User Interface (GUI) implemented with the VM Maestro Client Software. Cisco VIRL supports up to 20 Network Nodes. Therefore, you can build very complex Lab environments with this Virtual Lab. VIRL Main Features : These are some of the most important VIRL features: – Includes Official Cisco Images VIRL is the only Tool fully Licensed and approved by Cisco! – Automatic Configuration (done with the AutoNetkit Tool) – Multiple Network Platforms (IOSv, IOSvL2, NX-OSv, IOS XRv, IOS-XEv and ASAv Firewall). VIRL comes with a complete set of Legal and Fully Licensed Cisco IOS Images that are the same as those running on physical Routers & Switches. New Cisco IOS releases are provided in a regular basis. So you’ll always have the most up to date Virtual IOS Images! VIRL supports the classic IOS Images found in common ISR Routers and Layer 2 Switches: IOSv & IOSvL2 VIRL does not support Layer 3 Switches yet, but it might do so in the near future. In addition to the classic IOS Images, VIRL supports advanced Platforms such as IOS XRv & XRv 9000 (used in Service Provider environments) It also supports the ASAv Firewall , that can be used for Security related tasks. Finally, VIRL also supports IOS-XEv , which is the virtual version of the Cisco IOS XE Software that comes in the newest ISR Routers like the 42XX, 43XX and 44XX Series! GNS3 VM Features : These are some of the most important GNS3 VM features : – It supports Standard IOS (Legacy IOS) and VIRL IOS Images (GNS3 2.0 and higher) – Cisco Images are not embedded like in VIRL, so they must be obtained separately. By using VIRL Images, GNS3 provides support for IOS 15. X (IOSv, IOSvL2 & IOS XEv) – All work is done on the GNS3 Client PC! The GNS3 VM only provides back-end services. One of the traditional limitations of GNS3 is the fact that it doesn’t include ANY Cisco Images. So although you can download & install GNS3 for Free, normally you won’t be able to do anything with it. GNS3 users normally struggle trying to find IOS Images that can be imported into it. As mentioned above, GNS3 now can also import VIRL Images, which provides support for IOS 15. Bonus Software and Training Materials : This item includes a Disk (DVD) with the following Software and Training Materials : – VMware vSphere 6.0 Client Software – VMware ESXi 6.0 Operating System Installation Files (ISO CD Image) – mRemoteNG Connections Manager (provides Telnet/SSH access to the virtual devices) – VM Maestro Client Software (Maestro must be installed in a separate computer) – VIRL Training Videos Materials (Videos about the installation, configuration and use of VIRL) – GNS3 GUI and Server Software (GUI must also be installed in a separate computer) – GNS3 Training Videos Materials (Videos about the installation, configuration and use of GNS3). This Virtual Lab has been fully tested and. Therefore it’s guaranteed to work! I f you have any questions about the operation of this Virtual Lab, you can always count on us We’ve been providing Cisco Training Kits for years with hundreds of very satisfied customers! Please notice that due to the complex nature of this item we need. 2-3 days for processing. (it depends on where you live). Thank you for looking! The item “Cisco VIRL & GNS3 Server Dell R610 32GB VMware ESXi 6 CCNA CCNP CCIE Virtual Lab” is in sale since Saturday, May 17, 2014. This item is in the category “Computers/Tablets & Networking\Enterprise Networking, Servers\Servers, Clients & Terminals\Computer Servers”. The seller is “training.kits” and is located in Gainesville, Florida. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Mexico, Australia.

Model: R610
Number of Processors: 2
RAID Levels: 0
Memory (RAM) Capacity: 32GB
MPN: Does Not Apply
Processor Type: Xeon Quad Core
Brand: Dell
Processor Manufacturer: Intel

Dell Poweredge Server

Tag Archives: ccie